GAPS Water Treatment inline cartridges

CB1, Carbon 1 micron block

product

code

end

fitting

Chlorine, Taste & Odour reduction in a carbon block format. Unlike granular, block has no carbon fines to release, making it ideal for water filtration prior to point-of-use service equipment. The CB1 is also rated for cyst and cryptosporidium removal.

CB5, Carbon 5 micron block

product

code

end

fitting

A little cheaper than the 1 micron version but without cyst and cryptosporidium removal. Generally the CB5 version is used where the water supply would plug the 1 micron version if a pre-filter is not used.

LS, Carbon block with lead reduction

product

code

end

fitting

Similar to the CB1 with the addition of lead reduction.

Bitumous granular carbon, 20 micron

product

code

end

fitting

Entry level inline cartridges containing granular carbon. With a broad ability for taste, odour and chlorine removal as well as organic contamination.

RO, Coconut shell granular carbon, 5 micron

product

code

end

fitting

Costing just a little more than the standard carbon version, the coconut carbon has over 3
times the capacity. Having minimal effect on the pH of water, this is an ideal cartridge for
taste and odour improvements.

ALS, Coconut shell granualr carbon with scale control, 20 micron

product

code

end

fitting

Hexametaphosphate/Coconut Shell GAC.

EXTRA, Coconut carbon with bacteriostatic, 5 micron

product

code

end

fitting

Similar to the GS RO above with the addition of KDF 55D acting as a bacteriostatic media. Generally used where the cartridge has longer periods without being used. The KDF also increases the cartridge capacity.

CAL/RO, Coconut shell granular carbon with pH stabiliser, 20 micron

product

code

end

fitting

The CAL/RO incorporates calcite to balance the water to a natural pH with coconut carbon.

ULTRA, Coconut carbon with bacteriostatic with scale control
Price: £10.50 (£12.34 Including VAT at 17.5%)

end

fitting

The Ultra is an extension of the GS Extra with the addition of hexametaphosphate for inhibiting scale formation.

GS10ULTRA, 2" x 10", 5 micron, 20000 litre capacity, 4 lpm flow rate

EXTRA2/85, Coconut shell granular carbon with iron and sulphur reduction
Price: £27.50 (£32.31 Including VAT at 17.5%)

end

fitting

A specialist filter with a mix of coconut carbon and KDF85D for chlorine, taste, odour, iron and sulphur reduction.

GS210EXTRA2/85, 2.5" x 11", 5 micron, 20000 litre capacity, 2 lpm flow rate

PH, Scale control

product

code

end

fitting

Hexametaphosphate feeder for equipment protection from scaling.

DI, Total dissolved solids (TDS) reduction filter

product

code

High-capacity DI resin media commonly used in labs and laser systems.

Available only with 3/8" female threaded end connections

SED/5, sediment - rust - particulate reduction filters, 5 micron

product

code

end

fitting

Spun-bonded inline cartridges for particulate filtration to 5 micron.
Capable of far higher dirt-holding capacity than carbon media, acting as protection to the more expensive downstream cartridge.

Inline UV system

product

code

Pentek’s new inline ultraviolet light systems are the simple and safe way to protect a water supply from occasional intrusion of microbiological contamination. A choice of 3 sizes with flows of 2, 4 and 8 lpm attach inline with 1/4" push fittings. Power is supplied via a 110/240 volt transformer.

Inline cartridge clip
Too attach inline cartridges in place use a 2" or 2.5" clip
Price: £0.50 (£0.59 Including VAT at 17.5%)

size